3D Printing And Additive Manufacturing impact factor, indexing, ranking (2022)


3D

Aim and Scope

3D Printing And Additive Manufacturing is a research journal that publishes research related to Materials Science (miscellaneous). This journal is published by the Mary Ann Liebert. The P-ISSN of this journal is 23297662.

Also, check the other important details below like Publisher, ISSN, Ranking, Indexing, Impact Factor (if applicable), Publication fee (APC), Review Time, and Acceptance Rate of 3D Printing and Additive Manufacturing.

3D Printing And Additive Manufacturing Ranking

Impact Factor: 5.355
Total Citations: 1607
SJR (SCImago Journal Rank): 0.917
Quartile: Q1

The Impact Factor of 3D Printing And Additive Manufacturing is 5.355.

The impact factor (IF) is a measure of the frequency with which the average article in a journal has been cited in a particular year. It is used to measure the importance or rank of a journal by calculating the times its articles are cited.

The impact factor was devised by Eugene Garfield, the founder of the Institute for Scientific Information (ISI) in Philadelphia. Impact factors began to be calculated yearly starting from 1975 for journals listed in the Journal Citation Reports (JCR). ISI was acquired by Thomson Scientific & Healthcare in 1992, and became known as Thomson ISI. In 2018, Thomson-Reuters spun off and sold ISI to Onex Corporation and Baring Private Equity Asia. They founded a new corporation, Clarivate, which is now the publisher of the JCR.

Important Metrics

Journal Title: 3D Printing and Additive Manufacturing
Publisher: Mary Ann Liebert
P-ISSN: 23297662
Open Access: NO
Subject: Materials Science (miscellaneous)
Citescore: 6.8
SNIP: 1.36
SJR: 0.917
Quartile: 1

3D Printing and Additive Manufacturing Indexing

The 3D Printing and Additive Manufacturing is indexed in:

An indexed journal means that the journal has gone through and passed a review process of certain requirements done by a journal indexer.

The Web of Science Core Collection includes the Science Citation Index Expanded (SCIE), Social Sciences Citation Index (SSCI), Arts & Humanities Citation Index (AHCI), and Emerging Sources Citation Index (ESCI).


3D Printing And Additive Manufacturing Impact Factor 2022

The latest impact factor of 3D Printing and Additive Manufacturing is 5.355.

The impact factor (IF) is a measure of the frequency with which the average article in a journal has been cited in a particular year. It is used to measure the importance or rank of a journal by calculating the times it's articles are cited.


3D Printing And Additive Manufacturing Quartile

The latest Quartile of 3D Printing and Additive Manufacturing is Q1.

Each subject category of journals is divided into four quartiles: Q1, Q2, Q3, Q4. Q1 is occupied by the top 25% of journals in the list; Q2 is occupied by journals in the 25 to 50% group; Q3 is occupied by journals in the 50 to 75% group and Q4 is occupied by journals in the 75 to 100% group.



Call for Papers

Visit to the official website of the journal/ conference to check the details about call for papers.

How to publish in 3D Printing And Additive Manufacturing?

This journal covers the fields/ categories related to Materials Science (miscellaneous). If your research field is related to Materials Science (miscellaneous), then visit the official website of 3D Printing and Additive Manufacturing and send your manuscript.

Tips for publishing in 3D Printing And Additive Manufacturing:

  • Selection of research problem.
  • Presenting a solution.
  • Designing the paper.
  • Make your manuscript publication worthy.
  • Write an effective results section.
  • Mind your references.

Acceptance Rate

Acceptance rate is the ratio of the number of articles submitted to the number of articles published. Researchers can check the acceptance rate on the journal website. Even you can Contact the editor of the journal.

Journal Review Time

Journals usually ask reviewers to provide their reviews within 3-4 weeks. However, few journals have a mechanism to enforce the deadline, which is why it can be hard to predict how long the peer review process will take.

The review time also depends upon the quality of a research paper.


Final Summary

  • The impact factor of 3D Printing and Additive Manufacturing is 5.355.
  • It is published by Mary Ann Liebert.
  • The journal is indexed in UGC CARE, Scopus, SCIE.
  • The (SJR) SCImago Journal Rank is 0.917.
  • The 3D Printing and Additive Manufacturing is a reputed research journal.

Sources:

https://www.scopus.com/sourceid/21100779062







Similiar Journals


MECHANICS OF ADVANCED MATERIALS AND STRUCTURES
ISSN: 1537-6494
Publisher: TAYLOR & FRANCIS INC

CELLULOSE
ISSN: 0969-0239
Publisher: SPRINGER

POLYMERS & POLYMER COMPOSITES
ISSN: 0967-3911
Publisher: SAGE PUBLICATIONS LTD

ADVANCED FIBER MATERIALS
ISSN: 2524-7921
Publisher: SPRINGERNATURE

CERAMICS-SWITZERLAND
ISSN: 2571-6131
Publisher: MDPI

FUNCTIONAL COMPOSITES AND STRUCTURES
ISSN: 2631-6331
Publisher: IOP PUBLISHING LTD

JOURNAL OF DYNAMIC BEHAVIOR OF MATERIALS
ISSN: 2199-7446
Publisher: SPRINGERNATURE

BETON- UND STAHLBETONBAU
ISSN: 0005-9900
Publisher: ERNST & SOHN

COATINGS
ISSN: 2079-6412
Publisher: MDPI

DIAMOND AND RELATED MATERIALS
ISSN: 0925-9635
Publisher: ELSEVIER SCIENCE SA

Top 20 Journals

Credit and Source: Scopus, Clarivate, UGC CARE.