Additive Manufacturing impact factor, indexing, ranking (2023)

---

Aim and Scope

Additive Manufacturing is a research journal that publishes research related to Engineering; Materials Science. This journal is published by the Elsevier BV. The ISSN of this journal is 22148604. Based on the Scopus data, the SCImago Journal Rank (SJR) of Additive Manufacturing is 2.633.

Also, check the other important details below like Publisher, ISSN, Ranking, Indexing, Impact Factor (if applicable), Publication fee (APC), Review Time, and Acceptance Rate of Additive Manufacturing

According to Clarivate's JCR, the journals indexed in SCIE/SSCI have an impact factor.

Additive Manufacturing Ranking

The Impact Factor of Additive Manufacturing is 11.632.

The impact factor (IF) is a measure of the frequency with which the average article in a journal has been cited in a particular year. It is used to measure the importance or rank of a journal by calculating the times its articles are cited.

The impact factor was devised by Eugene Garfield, the founder of the Institute for Scientific Information (ISI) in Philadelphia. Impact factors began to be calculated yearly starting from 1975 for journals listed in the Journal Citation Reports (JCR). ISI was acquired by Thomson Scientific & Healthcare in 1992, and became known as Thomson ISI. In 2018, Thomson-Reuters spun off and sold ISI to Onex Corporation and Baring Private Equity Asia. They founded a new corporation, Clarivate, which is now the publisher of the JCR.

Important Metrics

Journal Title:	Additive Manufacturing
Publisher:	Elsevier BV
ISSN:	22148604
Type:	journal
Journal Scope:	Engineering; Materials Science
Country:	Netherlands
H-Index:	114
SJR:	2.633
Quartile:	Biomedical Engineering (Q1); Engineering (miscellaneous) (Q1); Industrial and Manufacturing Engineering (Q1); Materials Science (miscellaneous) (Q1)

Additive Manufacturing Indexing

The Additive Manufacturing is indexed in:

• UGC CARE
• Scopus
• Web of Science (SCIE)

An indexed journal means that the journal has gone through and passed a review process of certain requirements done by a journal indexer.

The Web of Science Core Collection includes the Science Citation Index Expanded (SCIE), Social Sciences Citation Index (SSCI), Arts & Humanities Citation Index (AHCI), and Emerging Sources Citation Index (ESCI).

Additive Manufacturing Impact Factor 2023

The latest impact factor of Additive Manufacturing is 11.632.

The impact factor (IF) is a measure of the frequency with which the average article in a journal has been cited in a particular year. It is used to measure the importance or rank of a journal by calculating the times it's articles are cited.

Note: Every year, The Clarivate releases the Journal Citation Report (JCR). The JCR provides information about academic journals including impact factor. The latest JCR was released in june, 2022. The JCR 2023 will be released on 30th June 2023.

Additive Manufacturing Quartile

The latest Quartile of Additive Manufacturing is Q1.

Each subject category of journals is divided into four quartiles: Q1, Q2, Q3, Q4. Q1 is occupied by the top 25% of journals in the list; Q2 is occupied by journals in the 25 to 50% group; Q3 is occupied by journals in the 50 to 75% group and Q4 is occupied by journals in the 75 to 100% group.

Call for Papers

Visit to the official website of the journal/ conference to check the details about call for papers.

How to publish in Additive Manufacturing?

If your research is related to Engineering; Materials Science, then visit the official website of Additive Manufacturing and send your manuscript.

Tips for publishing in Additive Manufacturing:

• Selection of research problem.
• Presenting a solution.
• Designing the paper.
• Make your manuscript publication worthy.
• Write an effective results section.
• Mind your references.

Acceptance Rate

Acceptance rate is the ratio of the number of articles submitted to the number of articles published. Researchers can check the acceptance rate on the journal website. Even you can Contact the editor of the journal.

Journal Publication Time

Journals usually ask reviewers to provide their reviews within 3-4 weeks. However, few journals have a mechanism to enforce the deadline, which is why it can be hard to predict how long the peer review process will take.

The review time also depends upon the quality of a research paper.

Final Summary

Sources: Additive Manufacturing

---